The SpeedyBee F7V3 50A Stack includes an F722 flight controller and 50A ESC, perfect for high-performance FPV quads. With Bluetooth and WiFi for wireless setup, it simplifies the tuning process. It also features 500MB of Blackbox storage for detailed flight logs.
SpeedyBee F7 V3 BL32 50A 30x30 Stack
Product Name SpeedyBee F7 V3 Flight Controller MCU STM32F722 IMU(Gyro) BMI270 USB Port Type Type-C Barometer BMP280 OSD Chip AT7456E chip BLE Bluetooth Supported. Used for Flight Controller configuration,built-in a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip Flash FC Firmware Wirelessly Supported. Please enter MENU > FC Firmware Flasher Download/Analyze Blackbox Supported.Please enter MENU > Blackbox Analyzer DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering. 6-pin DJI Air Unit Plug Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed. Flash(for BlackBox) 500MB BetaFlight Camera Control Pad Yes(CC pad on the front side) Power Input 3S - 6S Lipo 5V Output 10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A. 9V Output 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A. 3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load. 4.5V Output Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. ESC Signal Pads M1 - M4 on bottom side and M5-M8 on front side. UART 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6) ESC Telemetry UART R4(UART4) I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. LED Pad Used for WS2812 LED controlled by Betaflight firmware. Buzzer BZ+ and BZ- pad used for 5V Buzzer BOOT Button Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.RSSI Input Supported. Named as RS on the front side. SmartPort Supported Supported Flight Controller Firmware BetaFlight(Default),INAV Firmware Target Name SPEEDYBEEF7V3 Mounting 30.5 x 30.5mm( 4mm hole diameter) Dimension 41(L) x 38(W) x 8.1(H)mm Weight 10.7g Product Name SpeedyBee BL32 50A 4-in-1 ESC Firmware SpeedyBee BL32 50A Configurator Download Link http://github.com/bitdump/BLHeli/releases Continuous Current 50A * 4 Burst Current 55A(5seconds) TVS Protective diode Yes Heat Sink Yes External Capacitor 1000uF Low ESR Capacitor(In the package) ESC Protocol DSHOT300/600 PWM Frequency Range 16KHz-128KHz Power Input 3-6S LiPo Power Output VBAT Current Sensor Support (Scale=490 Offset=0) ESC Telemetry supported Mounting 30.5 x 30.5mm( 4mm hole diameter) Dimension 45.6(L) * 40(W) * 8.8mm(H) Weight 19.2g with heat sink The SpeedyBee F7V3 50A Stack is a powerhouse of performance and convenience. It includes an F722 flight controller paired with a 50A BLHeli_32 ESC, providing plenty of power for both freestyle and racing quads. With built-in Bluetooth and WiFi, you can wirelessly configure Betaflight or INAV settings, eliminating the need for a USB connection. The stack also includes 500MB of onboard Blackbox storage, which can hold hours of flight logs, perfect for fine-tuning your drone's performance. Whether you're a beginner or a pro, this stack offers everything you need to get flying quickly.
